(The bearing I spoke of in my previous post is a spare that came with a box of spare headstock and spindle parts I had purchased some time back.) Instead of the 10D-61 thrust bearing it has a solid steel spacer. The use of a lathe produces a finished product that is symmetrical along the axis of rotation.Qanthony87: Thinking about this further my 12" Atlas/Craftsman lathe it does not have the 10D-61 Thrust Bearing. A lathe functions by spinning the raw materials while cutting, drilling, sanding, knurling or deforming. Using a sophisticated computer software, the precision swis turning lathe can produce a near-finished product with minimal waste. Sturges, “Parts made with this system are indistinguishable from parts made on a swiss CNC machine-same accuracy, same repeatability, same quality.” In a sense, it’s the best of both worlds.Ī precision swis lathe is a computerized lathe used to create detailed solid objects from a single piece of wood or metal. Multi-axis capability is achieved on an existing machine in the shop. Indexing capability allows indexing the work and seamlessly transitions between milling and turning operations on the same part in the same setup. The Turning Head system can fill that void. “What they need is an economical way to create precision lathe parts.” “Machinists, engineering departments, automation groups, tool makers, mold makers and machine builders often don’t have the need for high-volume production,” Mr.
It’s hard to justify the expense of a multi-axis precision CNC lathe when only one, ten or 100 parts are required. Operating on the existing milling machine’s software, the CNC program provides fast, efficient operation without the need to learn new software.
The system allows the machinist to set up a job on a mill and crank out smooth, accurate parts in a repetitive way. The operator places a piece of stock in the spindle, tightens the collet, turns on the unit, and hits “Go” on the CNC interface. The toolholders are available in three sizes (1/32 radius, 1/64 radius and 1/128 radius) and maintain cutter concentricity to less than 0.001-inch TIR. Tool changes between different turning operations are eliminated. The universal design allows left-hand, right-hand and center cutting operations simply by rotating the tool. The system comes with a set of three turning bars, each with an R8 or 3/4-inch straight. It has a large, through-bore 5C spindle with a 4-degree taper mount nose. The standard model has less than 50 millionths of an inch runout, and the super-precision model has less than 20 millionths. The Turning Head spindle-the equivalent of a lathe headstock-is made of steel and cast iron and uses premier Grade 7 pre-loaded ball bearings that are lubricated for life. An optional cross slide accessory bolts onto the table, allowing for plunge operations such as parting and grooving. So we developed a turning bar toolholder that places the tip of the tool at the spindle’s center of rotation, eliminating the slight play in the tool tip and providing the precision and accuracy needed for professional, high-quality swis type automatic lathe work on a mill.” Based on this principle, the company built the prototype for the Turning Head system, which is capable of external turning, facing and contouring operations. “The problem is, even if you attach a lathe tool to the mill spindle and lock it, there’s still a tiny bit of play that makes it impossible to maintain a standard of precision. “I had always wondered why we couldn’t somehow do precision CNC lathe work on a CNC milling machine,” Mr. To address the issue, the company developed what it calls the Sturges Turning Head system to bridge the gap between traditional, full-featured CNC lathes and low-productivity, small CNC mini lathes. He considered a CNC mini lathe, but found that it would not be precise, rigid or accurate enough for the work required. “CNC lathes are expensive, take up much needed floor space, and have a steep learning curve,” explains Dan Sturges, company CEO. The company was working with a client who needed a special machine built that required substantial CNC lathe work. Such was the case for Sturges DesignWorks, a company in Portland, Ore., that provides automation and design engineering solutions in a variety of industries, including medical products, electronics, fixturing and tooling, and research and development. But when it needs to produce precision turned parts, even if for a very small lot size, the shop needs a solution. Sometimes a shop doesn’t do enough turning work to justify the purchase of a CNC lathe.